AD2Pi and SmartThings integration error

[jasonsf]

I can also confirm that the new code works on the Master branch.

Jason

[Lyubo]

Hello,
I was able to install and get everything running with the updated code, however i have a little problem:

When the alarm is on, the device in the app keeps switching between armed and disarmed and after about 15-20 minutes turns the alarm off.
This is what I see under the device history:
https://www.screencast.com/t/wL8LHCtUbR

Any ideas what may cause that?

I will remove and redo everything this weekend in case I did something wrong.
Thanks,
Lyubo

[mathewss]

You probably have multiple partitions. Send us raw messages from the alarmdecoder to confirm. Fix would be to setup the address mask to only watch one partition.

Best
Sean

[Lyubo]

Thanks for the quick reply Sean! How can I get the raw messages from the alarmdecoder?
Thanks,
Lyubo

[mathewss]

You can use the "Log" menu/tab on the webApp then select Live and you can "Copy"

Best
Sean

[Lyubo]

Sorry for the long delay.
Here is what the log look like after I turn on the alarm:
2017-12-14 16:34:55 !RFX:0635639,04
2017-12-14 16:34:51 [00100001000000003A--],008,[f760000f1008008c08020000000000],"ARMED ***STAY*** "
2017-12-14 16:34:50 [10000001100000003A--],008,[f70000300008001c28020000000000]," DISARMED CHIME Ready to Arm "
2017-12-14 16:34:44 [00100001000000003A--],008,[f760000f1008008c08020000000000],"ARMED ***STAY*** "
2017-12-14 16:34:39 [10000001100000003A--],008,[f70000300008001c28020000000000]," DISARMED CHIME Ready to Arm "
2017-12-14 16:34:37 !RFX:0088367,04
2017-12-14 16:34:30 [00100001000000003A--],008,[f760000f1008008c08020000000000],"ARMED ***STAY*** "
2017-12-14 16:34:29 [10000001100000003A--],008,[f70000300008001c28020000000000]," DISARMED CHIME Ready to Arm "
2017-12-14 16:34:20 [00100001000000003A--],008,[f760000f1008008c08020000000000],"ARMED ***STAY*** "
2017-12-14 16:34:19 [10000001100000003A--],008,[f70000300008001c28020000000000]," DISARMED CHIME Ready to Arm "
2017-12-14 16:34:14 [00100001000000003A--],008,[f760000f1008008c08020000000000],"ARMED ***STAY*** "
2017-12-14 16:34:09 [10000001100000003A--],008,[f70000300008001c28020000000000]," DISARMED CHIME Ready to Arm "
2017-12-14 16:34:01 [00100001000000003A--],008,[f760000f1008008c08020000000000],"ARMED ***STAY*** "
2017-12-14 16:33:59 [10000001100000003A--],008,[f70000300008001c28020000000000]," DISARMED CHIME Ready to Arm "
2017-12-14 16:33:53 !RFX:0165293,04
2017-12-14 16:33:51 [00100001000000003A--],008,[f760000f1008008c08020000000000],"ARMED ***STAY*** "

It just goes between armed and disarmed and after awhile it turns off the alarm.
I appreciate any help with this issue.
Thanks,
Lyubo

[kevin]

These are definitely messages for 2 different partitions.

You can adjust your address mask to filter out the 2nd partition if it's not in use - or figure out how to disable it via programming.

[Lyubo]

Thanks, Kevin!
I tried to do it by programming the panel, but that didn't change anything.
How would change the address mask? Sorry, this is all new to me...
Thanks,
Lyubo

[kevin]

In the device setup process there is an "Address Mask" field with an address mask builder, you can select which keypad addresses you want to listen to - you can even put in an existing address mask to find out what addresses it encompasses.

You can find how to calculate the address mask in the protocol documentation from the documentation link in the website header

[Lyubo]

Thanks Kevin! That worked.

I have a different issue now. I cant see any of the zones. here is the error I get in the webapp:

https://www.screencast.com/t/QdBqZHBYX2

Any ideas what may cause that?

Thanks,
Lyubo