Commands

Command	Description
=	Reboot the device.
!	Configure the device via prompts.
C	Sets or retrieves configuration parameters.
L	Emulate virtual zone opens and closes.
\x01\x01\x01	Send Function Key #1
\x02\x02\x02	Send Function Key #2
\x03\x03\x03	Send Function Key #3
\x04\x04\x04	Send Function Key #4
0123456789*#	Send key to panel

Device Configuration

The AlarmDecoder configuration viewed or modified in one of two ways: prompted or programmatically.

Name	Default Value	Valid Values (Regex)	Description
ADDRESS	18	[0-9]{2}	Keypad address assigned to the AlarmDecoder.
CONFIGBITS	FF00	[0-9a-f]{4}	Special settings for the device. See CONFIGBITS for more information.
MASK	FFFFFFFF	[0-9a-f]{8}	Address mask used to filter for keypad alphanumeric messages.
EXP	NNNNN	[YN]{5}	Emulation of zone expanders 1-5
REL	NNNNN	[YN]{4}	Emulation of relay expanders 1-4
LRR	N	[YN]	Emulation of Long Range Radio expander
DEDUPLICATE	N	[YN]	If enabled, removes duplicate alphanumeric keypad messages.

Prompted

If you send ! followed by a carriage return you will be prompted for each field. This prompt also includes a basic description of the setting as well as it's current value.

You may hit enter to keep the current value or enter a new one.

Example:

!>Ademco/DSC  Mode A/D  (A) :>
!>Keypad Address       (18) :>
!WARNING. Do not enable a module if the physical module exists on the system.
!Zone Expanders Y/N Max allowed: 02
!>expander module #01 ZN 09-16 (N) :>
!>expander module #02 ZN 17-24 (N) :>
!>expander module #03 ZN 25-32 (N) :>
!>expander module #04 ZN 33-40 (N) :>
!>expander module #05 ZN 41-48 (Y) :>
!Relay Modules Y/N Max allowed: 04
!>relay module #01 (Y) :>
!>relay module #02 (N) :>
!>relay module #03 (N) :>
!>relay module #04 (N) :>
!>Emulate Long Range Radio Y/N: (Y) :>
!>ZoneTracker track zone restore Y/N: (N) :>
!>Address Filter Mask  (ffffffff) :>
!>Deduplicate          (N) :>
!>Config Bits        (ff04) :>

Programmatically

You may retrieve all of the devices settings by sending C to the panel followed by a carriage return (\r).

Retrieving AlarmDecoder settings:

• Send: C\r
• Response: !CONFIG>ADDRESS=18&CONFIGBITS=ff00&LRR=N&EXP=NNNNN&REL=NNNN&MASK=ffffffff&DEDUPLICATE=N

It can also be used to set values:

• Send: CADDRESS=20\r
• Response: !>ADDRESS=20

The same command may be used to set multiple values:

• Send: CADDRESS=20&DEDUPLICATE=Y\r
• Response: !>ADDRESS=20&DEDUPLICATE=Y

Message Types

There are several types of messages produced by the AlarmDecoder. These include: Keypad, Relay Expander, Zone Expander, RFX, LRR, and AUI.

Keypad

Keypad Format

[001000010000--------],010,[f70700060010808c08020000],"ARMED ***STAY** ZONE BYPASSED "
Bit field	Numeric code	Raw data	Alphanumeric Keypad Message
[001000010000--------]	010	[f70700060010808c08020000]	"ARMED ***STAY** ZONE BYPASSED "

Zone Expander

 !EXP Format

!EXP:07,01,01
Header	Zone Expander Address	Expander Channel	Data
!EXP	07	01	01

Relay Expander

 !REL Format

!REL:12,01,01
Header	Relay Expander Address	Expander Channel	Data
!REL	12	01	01

RFX

 !RFX Format

!RFX:0180036,80
Header	Serial Number	Data
!RFX	0180036	80

LRR

 !LRR Format

!LRR:012,1,ARM_STAY
Header	Event Data	Partition	Event Type
!LRR	012	1	ARM_STAY

AUI

TODO