Commands

Command	Description
=	Reboot the device.
!	Configure the device via prompts.
C	Sets or retrieves configuration parameters.
L	Emulate virtual zone opens and closes.
\x01\x01\x01	Send Function Key #1
\x02\x02\x02	Send Function Key #2
\x03\x03\x03	Send Function Key #3
\x04\x04\x04	Send Function Key #4
0123456789*#	Send key to panel

Reboot

TODO

Zone Emulation

TODO

Function Keys

TODO

Device Configuration

The AlarmDecoder configuration can be viewed or modified in one of two ways: prompted or programmatically.

Name	Default Value	Valid Values (Regex)	Description
ADDRESS	18	[0-9]{2}	Keypad address assigned to the AlarmDecoder.
CONFIGBITS	FF00	[0-9a-f]{4}	Special settings for the device. See CONFIGBITS for more information.
MASK	FFFFFFFF	[0-9a-f]{8}	Address mask used to filter for keypad alphanumeric messages.
EXP	NNNNN	[YN]{5}	Emulation of zone expanders 1-5
REL	NNNNN	[YN]{4}	Emulation of relay expanders 1-4
LRR	N	[YN]	Emulation of Long Range Radio expander
DEDUPLICATE	N	[YN]	If enabled, removes duplicate alphanumeric keypad messages.

CONFIGBITS

CONFIGBITS is a setting that's used to enable special functionality on the AlarmDecoder. You can enable these by masking the correct bits.

Mask	Description
0x0001	Enable reporting of AUI messages.
0x0002	Enable reporting of keypress events.
0x0004	Disable prompts for L and | commands.
0x0008	Enable the prefixing of panel messages with !KMP.
0x0100	Enable reporting of RFX messages.

Prompted

If you send ! followed by a carriage return you will be prompted to configure each field. This prompt also includes a basic description of the setting as well as it's current value.

You may hit enter to keep the current value or provide a new one.

Example:

!>Ademco/DSC  Mode A/D  (A) :>
!>Keypad Address       (18) :>
!WARNING. Do not enable a module if the physical module exists on the system.
!Zone Expanders Y/N Max allowed: 02
!>expander module #01 ZN 09-16 (N) :>
!>expander module #02 ZN 17-24 (N) :>
!>expander module #03 ZN 25-32 (N) :>
!>expander module #04 ZN 33-40 (N) :>
!>expander module #05 ZN 41-48 (Y) :>
!Relay Modules Y/N Max allowed: 04
!>relay module #01 (Y) :>
!>relay module #02 (N) :>
!>relay module #03 (N) :>
!>relay module #04 (N) :>
!>Emulate Long Range Radio Y/N: (Y) :>
!>ZoneTracker track zone restore Y/N: (N) :>
!>Address Filter Mask  (ffffffff) :>
!>Deduplicate          (N) :>
!>Config Bits        (ff04) :>

Programmatic

You may retrieve all of the current device settings by sending C to the panel followed by a carriage return (\r).

Retrieving settings:

• Send: C\r
• Response: !CONFIG>ADDRESS=18&CONFIGBITS=ff00&LRR=N&EXP=NNNNN&REL=NNNN&MASK=ffffffff&DEDUPLICATE=N

It can also be used to set values:

• Send: CADDRESS=20\r
• Response: !>ADDRESS=20

The same command may be used to set multiple values:

• Send: CADDRESS=20&DEDUPLICATE=Y\r
• Response: !>ADDRESS=20&DEDUPLICATE=Y

Message Types

There are several types of messages produced by the AlarmDecoder. These include: Keypad, Relay Expander, Zone Expander, RFX, LRR, and AUI.

Keypad

Keypad messages are by far the most common message type produced by the AlarmDecoder. These messages also have an optional header that can be enabled in the CONFIGBITS. This setting prefixes all keypad messages with !KPM:.

Keypad Format

[001000010000--------],010,[f70700060010808c08020000],"ARMED ***STAY** ZONE BYPASSED "
Bit field	Numeric code	Raw data	Alphanumeric Keypad Message
[001000010000--------]	010	[f70700060010808c08020000]	"ARMED ***STAY** ZONE BYPASSED "

Zone Expander

 !EXP Format

!EXP:07,01,01
Header	Zone Expander Address	Expander Channel	Data
!EXP	07	01	01

Relay Expander

 !REL Format

!REL:12,01,01
Header	Relay Expander Address	Expander Channel	Data
!REL	12	01	01

RFX

 !RFX Format

!RFX:0180036,80
Header	Serial Number	Data
!RFX	0180036	80

LRR

 !LRR Format

!LRR:012,1,ARM_STAY
Header	Event Data	Partition	Event Type
!LRR	012	1	ARM_STAY

AUI

TODO

Keypress Events

TODO